Search results for "Electric generator"
showing 10 items of 51 documents
Performance evaluation and stability of silicide-based thermoelectric modules
2020
Abstract Long-term studies on thermoelectric generators based on N-type magnesium silicide (Mg2.01Si0.49Sn0.5Sb0.01) and P-type higher manganese silicide (Mn0.98Mo0.02Si1.73Ge0.02) materials are presented, in the operating temperature range of 200 °C–400 °C. Emphasis is put on the performance and reliability of the current collector configuration, especially on the hot side of the module, and on the thermomechanical stresses that are created during operation and lifetime testing as a result of large temperature gradients experienced across the thermoelectric legs. With silver (Ag) paste as contact material, the long term-stability of the uni-couples was carried out on non-metalized legs and…
A Planar Generator for a Wave Energy Converter
2019
This article presents a permanent magnet planar translational generator which is able to exploit multiple modes of sea wave energy extraction. Linear electrical generators have recently been studied for the exploitation of sea wave energy, but, to the best of our knowledge, no synchronous planar translational generator has been proposed. In this article, to maximize the energy extraction, we have considered all the potential modes of motion due to wave excitation and included them within the mathematical model of the proposed system. The principle of operation of the generator can be summarized as follows: the moving part (translator) of the generator is driven from the sea waves and induce…
Long term stability testing of oxide unicouple thermoelectric modules
2019
Thermoelectric devices based on oxides are good candidates for energy harvesting technologies for use in aggressive conditions where the materials should withstand high temperatures and corrosive environments over prolonged time. This leads to a natural concern for the stability of the electrical contacts, especially on the hot side of the module. In this work, we have assembled several prototype unicouple thermoelectric modules made by pyrolyzed and spark plasma sintered n-type CaMnO3 and p-type Ca3Co4O9 and then tested under different conditions mimicking end-user applications. For baseline experiments we have chosen to use nickel as the contact material in order to show the effect of its…
Hybrids composites of NCCO/PEDOT for thermoelectric applications
2017
Abstract Organic materials are becoming a realistic roadway to fabricate efficient thermoelectric devices using environmental friendly materials. Such requirements are actually fulfilled by thermoelectric generators operating by conducting polymers, but also by hybrid materials. The combination of organic + inorganic compounds may exhibit a high electrical conductivity and Seebeck coefficient as well as lower thermal conductivity in order to efficiently generate thermoelectric power. In these hybrid compounds, perovskite-type oxides are a suitable election for the inorganic part since they have a high Seebeck coefficient although their electrical conductivity is usually low. Blending them w…
Performance of a thermoelectric module based on n-type (La0.12Sr0.88)0.95TiO3-δ and p-type Ca3Co4-xO9+δ
2020
Here, we present the performance of a thermoelectric (TE) module consisting of n-type (La0.12Sr0.88)0.95TiO3 and p-type Ca3Co4-xO9+δ materials. The main challenge in this investigation was operation of TE module in different atmosphere conditions, since n-type has its optimum TE-performance at reducing, while p-type at oxidizing conditions. The TE module was exposed to two different atmospheres and demonstrated higher stability in N2 atmosphere than in air. The maximum electrical power output decreased after 40 h when the hot side was exposed to N2 at 600 °C, while only 1 h at 400 °C in ambient air was enough to oxidize (La0.12Sr0.88)0.95TiO3 followed by a reduced electrical power output. T…
A software for the evaluation of winding factor harmonic distribution in high efficiency electrical motors and generators
2013
In this paper a software developed for the determination of winding connections, the calculation of winding factors and the evaluation of their harmonic distribution of three and two phase windings is presented by using as input data simply the number of slots, pole pairs and phases. The software is implemented as a function in MATLAB environment. By means of some examples, covering the most relevant winding types, the capabilities of this software will be shown. Particularly, integer and fractional single and double layer winding can be treated. Some examples are presented and briefly discussed. The connections, the winding factor harmonic distribution, the electro-motive force (e.m.f) THD…
Design, assembly and characterization of silicide-based thermoelectric modules
2016
ID: 1143 In: Energy conversion and management, 13-21. Summary: Highlights•Novel silicide-based thermoelectric modules were experimentally investigated.•The modules produced high power of 1.04 W at 405 °C and 3.24 W at 735 °C.•An estimated module efficiency of 5.3% represent the highest reported for silicide systems.AbstractSilicides have attracted considerable attention for use in thermoelectric generators due mainly to low cost, low toxicity and light weight, in contrast to conventional materials such as bismuth and lead telluride. Most reported work has focused on optimizing the materials properties while little has been done on module testing. In this work we have designed and tested mod…
25-kW/50-kHz generator for induction heating
1991
The authors present the features, technology, and construction of a transistorized generator for induction heating operating over the 4-50 kHz frequency range. This type of 25 kW output-power generator allows replacement of the electronic tube generators for most of their applications. The advantages of this new generator are more energy efficiency, extended life, reduced size, separated heating station of the generator, and connection by flexible cable. In addition, the generator has incorporated a frequency automatic tracking system that allows operating without any adjustments over a wide frequency range. >
Novel test bed for induction heating power supplies
2006
Power supplies used in induction heating industrial applications must be entirely tested after its manufacturing in order to assure its security and reliability by means of a full power running test of several hours of duration. Nowadays this test is done with a dissipative load which implies a large waste of energy. This paper proposes a new high efficiency test system for induction heating generators. It incorporates a regenerative electronic load which allows an extraordinary improvement of the efficiency of this test with an important economical and ecological benefit.
Analysis of the maximization of wind turbine energy yield using a continuously variable transmission system
2017
Abstract In this paper, an analytic study of the subject of mechanical power transmission in HAWT wind turbine has been carried out. For the most part, the study analyzes the use of continuously variable transmission (CVT) in order to allow the turbine and the electric generator to couple, allowing in turn, an unremitting transmission ratio adjustment. In low-wind sites, the design criteria suggest an oversizing of the wind turbine in order to generate adequate electrical power even at low wind speed. The proposed solution enhances the space of operating points since it allows the electric generator to release the rotational speed from the turbine one (limited due to structural integrity). …